Getting Started with Plumber's Essentials When Installing a Bathtub
Getting Started with Plumber's Essentials When Installing a Bathtub
Blog Article
Every person has got their personal way of thinking with regards to How to Install a Bathtub.
Installing a tub isn't specifically brain surgery, yet it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is readily obtainable, the job can relocate rapidly; if you have to open a wall surface to remove the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the work and also fit attempting it. Instead of hiring a professional to take over a halfway-completed project, it is much better to think about employing one prior to you begin. Possibilities are you might need a professional plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your shower room if you have already acquired a new tub and also do not require to change the arrangement of your previous water supply pipes.
Your devices and material list ought to consist of the following:
Getting ready for the Installation
To start with, the supporting structure provided with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of the two taps using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the supply of water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather problematic due to the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Before going on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using the two wooden boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the bath tub till the level reads degree.
To set up faucets, fit the bottom of the outermost adaptable tap port to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water system and inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the bathtub must wait until the bathtub has actually been made use of at least once as this will settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in location in between the faucet as well as the sink. Safeguard the tap in position with the maker offered backnut. As soon as the faucet is securely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former type should be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, causing the water to penetrate the wall surface between the bathroom and also the tiling, causing complications with dampness and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your components as well as installations. They are sold in tubes and cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can split rather early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
As an avid person who reads about Tools You Need to Install a New Bathtub , I figured sharing that excerpt was essential. Sharing is caring. Helping people is fun. Many thanks for going through it.
Burst pipe? Phone! Report this page